brass stair rods from stair rods uk
Stair Rods UK
How to measure stair and install stair rods

All stair rods, apart from (Homepride, Easyrods, Blacksmith and Stargrip) are made to measure, so we need a tip to tip measurement for them, including the finial. Whilst the majority of stairs have a regular distance between the edge of the carpet and the stringboard or spindles, check to see if a newel post or other obstruction affects the required length of rod on that step. The guide below gives information on measuring and installing stair rods.

Measuring Stair Rods

When measuring for stair rods, we have recommendations for the rod lengths:

All 1/2" (12.5mm) diameter rods, Tudor, Crystal, Vision, Homepride, Blacksmith Flat and Ball:
stair rods should be 4"/10cm over the width of the carpet (2"/5cm each side)

All 5/8" (16mm) diameter rods:
rods should be 5"/12.5cm over the width of the carpet (2.5"/6.25cm each side)

All 3/4" (19mm) diameter rods, Royale, Eastern Promise & Blacksmith Spear:
rods should be 6"/15cm over the width of the carpet (3"/7.5cm each side)

  
Measuring stair rods
We recommend fitting a stair rod on the bottom step.  
Installing stair rods
 
When fitting Posh, Joints or Symwood, ensure the wings of the door thresholds are over the gripper as shown.  
Installing door thresholds
 

Installing Stair Rods

The bracket should sit on the stair case itself, directly alongside the carpet. Make bradawl guide holes for the screws and then screw the bottom half of the bracket to the stair. Do the same on the other side and then lay the stair rod in the brackets and screw the top half of the bracket to the bottom, ensuring the rod is protruding an equal amount on each end.

On no account should the top and bottom of each hinged bracket be mixed as they are a set, they cannot be interchanged with the other brackets, so we recommend not mixing the bracket components when preparing them for fitting. Note:Stair rods are for decorative use only, the carpet must be secured by another means.

Winder solutions with Stair Rods
Fitting stair rods onto turning stairs (winders) is very easy to do. We can supply our Universal Bracket (pictured right) for most of our ranges - this is an extremely simple bracket that is fitted with only one screw.   Fitting carpet winders with our Universal Bracket
   

Right: Another view of our Universal Bracket.

This bracket can also be used to fit stair rods on Fully Fitted (full width) carpets.

Fitting the carpet with Easybind means the fitter can measure, cut and fit winders on site, without having to take the carpet away to be bound.

   Fitting carpet winders with our Universal Bracket
 
Right: Another elegant solution to fitting stair rods on winder carpets - notch the carpet to provide space for fixing bracket.

Image courtesy of Borderline Carpet Planning Services, London 		 
Fitting carpet winders
 
 

Curving Stair Rods

The Following ranges can be bent, to suit curved stairs:

Premier (excluding Hanover), Country (PLAIN rods only), Eastern Promise (PLAIN rods only), Vision, Crystal and Blacksmith.

We have a PDF guide for making templates, click here

 

Stair Rods FAQ's
Will our products need polishing?
No, all our brass products have a clear laquer that prevents them from tarnishing. To clean, simply wipe with a damp cloth. DO NOT use metal cleaning products as this will damage the laquer, causing tarnishing and damage to any finish you may have chosen.

Can stair rods be altered once ordered?
No. It is vital to carefully measure the rods before ordering to ensure the lengths are correct as they cannot be altered once they have been made.

Can the rods be used as the sole means of securing the carpet?
No, we strongly recommend that the carpet is installed by other means. Fitting the carpet correctly increases its lifespan and improves the safety of the stair case.

 
© Stairrods (UK) Ltd